usbd_conf.h 3.9 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596
  1. /*!
  2. \file usbd_conf.h
  3. \brief usb device driver basic configuration
  4. \version 2023-06-30, V2.1.6, firmware for GD32F30x
  5. */
  6. /*
  7. Copyright (c) 2023, GigaDevice Semiconductor Inc.
  8. Redistribution and use in source and binary forms, with or without modification,
  9. are permitted provided that the following conditions are met:
  10. 1. Redistributions of source code must retain the above copyright notice, this
  11. list of conditions and the following disclaimer.
  12. 2. Redistributions in binary form must reproduce the above copyright notice,
  13. this list of conditions and the following disclaimer in the documentation
  14. and/or other materials provided with the distribution.
  15. 3. Neither the name of the copyright holder nor the names of its contributors
  16. may be used to endorse or promote products derived from this software without
  17. specific prior written permission.
  18. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  19. AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
  20. WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
  21. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
  22. INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
  23. NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
  24. PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
  25. WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  26. ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
  27. OF SUCH DAMAGE.
  28. */
  29. #ifndef __USBD_CONF_H
  30. #define __USBD_CONF_H
  31. #include "gd32f30x.h"
  32. #include "gd32f303e_eval.h"
  33. #define USBD_CFG_MAX_NUM 1U
  34. #define USBD_ITF_MAX_NUM 1U
  35. #define USBD_IAP_INTERFACE 0U
  36. /* define if low power mode is enabled; it allows entering the device into DEEP_SLEEP mode
  37. following USB suspend event and wakes up after the USB wakeup event is received. */
  38. /* #define USBD_LOWPWR_MODE_ENABLE */
  39. /* endpoint count used by the custom HID device */
  40. #define EP_COUNT (2U)
  41. /* base address offset of the allocation buffer, used for buffer descriptor table and packet memory */
  42. #define BTABLE_OFFSET (0x0000U)
  43. #define USB_STRING_COUNT 4U
  44. /* USB feature -- Self Powered */
  45. /* #define USBD_SELF_POWERED */
  46. /* endpoint0, Rx/Tx buffers address offset */
  47. #define EP0_RX_ADDR (0x40U)
  48. #define EP0_TX_ADDR (0x80U)
  49. #define IAP_IN_EP EP_IN(1U)
  50. #define IAP_OUT_EP EP_OUT(1U)
  51. #define IAP_IN_PACKET 17U
  52. #define IAP_OUT_PACKET 64U
  53. /* Tx buffer address offset */
  54. #define INT_TX_ADDR (0x100U)
  55. /* Rx buffer address offset */
  56. #define INT_RX_ADDR (0x140U)
  57. #define TRANSFER_SIZE 62U /* IAP maximum data packet size */
  58. #define PAGE_SIZE 2048U /* MCU page size */
  59. /* memory address from where user application will be loaded, which represents
  60. the DFU code protected against write and erase operations.*/
  61. #define APP_LOADED_ADDR 0x08008000U
  62. /* maximum number of supported memory media (Flash, RAM or EEPROM and so on) */
  63. #define MAX_USED_MEMORY_MEDIA 1
  64. /* make sure the corresponding memory where the DFU code should not be loaded
  65. cannot be erased or overwritten by DFU application. */
  66. #define IS_PROTECTED_AREA(addr) (uint8_t)((((addr) >= 0x08000000U) && ((addr) < (APP_LOADED_ADDR)))? 1U : 0U)
  67. #define USB_PULLUP GPIOG
  68. #define USB_PULLUP_PIN GPIO_PIN_8
  69. #define RCU_AHBPeriph_GPIO_PULLUP RCU_GPIOG
  70. #endif /* __USBD_CONF_H */