/*! \file main.c \brief TIMER1 oc toggle demo for gd32f30x \version 2017-02-10, V1.0.0, firmware for GD32F30x \version 2018-10-10, V1.1.0, firmware for GD32F30x \version 2018-12-25, V2.0.0, firmware for GD32F30x \version 2020-09-30, V2.1.0, firmware for GD32F30x */ /* Copyright (c) 2020, GigaDevice Semiconductor Inc. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of the copyright holder nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #include "gd32f30x.h" #include #include "gd32f307c_eval.h" void gpio_config(void); void timer_config(void); /*! \brief configure the GPIO ports \param[in] none \param[out] none \retval none */ void gpio_config(void) { rcu_periph_clock_enable(RCU_GPIOA); rcu_periph_clock_enable(RCU_AF); /*configure PA1(TIMER1 CH1) as alternate function*/ gpio_init(GPIOA,GPIO_MODE_AF_PP,GPIO_OSPEED_50MHZ,GPIO_PIN_1); } /*! \brief configure the timer peripheral \param[in] none \param[out] none \retval none */ void timer_config(void) { /* --------------------------------------------------------------------------- TIMER1 configuration: output compare toggle mode: TIMER1CLK = systemcoreclock / 6000=20K, CH1 update rate = TIMER1 counter clock / CH1VAL = 20000/4000 = 5 Hz ----------------------------------------------------------------------------*/ timer_oc_parameter_struct timer_ocintpara; timer_parameter_struct timer_initpara; rcu_periph_clock_enable(RCU_TIMER1); timer_deinit(TIMER1); /* TIMER1 configuration */ timer_initpara.prescaler = 5999; timer_initpara.alignedmode = TIMER_COUNTER_EDGE; timer_initpara.counterdirection = TIMER_COUNTER_UP; timer_initpara.period = 3999; timer_initpara.clockdivision = TIMER_CKDIV_DIV1; timer_initpara.repetitioncounter = 0; timer_init(TIMER1,&timer_initpara); /* CH1 configuration in OC TOGGLE mode */ timer_ocintpara.outputstate = TIMER_CCX_ENABLE; timer_ocintpara.outputnstate = TIMER_CCXN_DISABLE; timer_ocintpara.ocpolarity = TIMER_OC_POLARITY_HIGH; timer_ocintpara.ocnpolarity = TIMER_OCN_POLARITY_HIGH; timer_ocintpara.ocidlestate = TIMER_OC_IDLE_STATE_LOW; timer_ocintpara.ocnidlestate = TIMER_OCN_IDLE_STATE_LOW; timer_channel_output_config(TIMER1,TIMER_CH_1,&timer_ocintpara); timer_channel_output_pulse_value_config(TIMER1,TIMER_CH_1,3999); timer_channel_output_mode_config(TIMER1,TIMER_CH_1,TIMER_OC_MODE_TOGGLE); timer_channel_output_shadow_config(TIMER1,TIMER_CH_1,TIMER_OC_SHADOW_DISABLE); /* auto-reload preload enable */ timer_auto_reload_shadow_enable(TIMER1); timer_enable(TIMER1); } /*! \brief main function \param[in] none \param[out] none \retval none */ int main(void) { gpio_config(); timer_config(); while (1); }